Use it like a real lift. Warning : Loud and high-pitched sounds ! Next part of the description : But hi, don’t worry, this heap of [censored] is still way better than a lift like Dellios and any other kirk time lifts. But I let @LiftFan2021 tell us if it is better or worse than a Kotori Minami lift. This lift will be closed down the 28/04/ 2023 and it will be sent up and down until it collapse the 28/04/2023 and 29/04/2023 by APEX Lifts. And then, the collapsed structure will be taken out of the shaft, same as the doors and all the fixtures. All the pipes and wires will also be removed. The tank and logic cabinet will be removed aswell. The shaft will later be cleaned out and they will install a brand new 2023 generic APEX MRL traction lift with Ziehl Abegg Zetadyn VF drive and motor, Schaefer MT 42 buttons, Meiller Türen door operator, Lester Controls Almega 2 full-intelligent logic controller and Lester Controls TC3 indicators. This lift is also the last remaining Russo Elevators Inc 1rst generation lift as Antonio Russo (The person who created Russo Elevators Inc. and it’s a fictional character) has installed a remote monitoring system on all of his lifts to tell if the lift is still original or not. According to that monitoring system, loads of Russo 1rst Generation lifts have been modded or completely replaced between November 2020 and February 2023, the 3/4 of them were replaced with nasty and utterly cancerous and disgusting kirk time lifts which uses awful STEP buttons, appallingly bad ULCEP 4 logic control systems and horrendous Selcom (An Italian door brand that was created by Wittur) HydraPlus (Or what I and my other accounts call more HydraPoo) doors that screeches and goes « SRERK » (Even GAL is way better) or modded by Jackson Lift Group with Lester Controls Almega 2 logic with bad setup, flimsy and dull Lester PB4 buttons, basic Lester TC3 indicators and horrible screechy Wittur Hydraplus doors. As of February 2023, the 2nd last remaining Russo Elevators Inc. 1rst Gen lift ever built gets Oroned (Modded by Orona) and this one will be removed and Lestered by APEX Lifts. So, Russo 1rst Gen lift will soon be completely extinct as original. Infos about the manufacturer : Antonio Russo has built a lift factory and some headquarters in September 2008. The 1rst day of November 2008, he created the brand Russo Elevators Inc. Their 1rst lift (This one) has been installed/commissionned the 07/11/2008. This lift has 6 days left before collapsing according to APEX, it will be taken out of service the 28/04/2023 and the cab and ram will be sent up and down the 28th and 29th of 04/2023. When it will be collapsed, all of the hydraulic fluid will be pumped and eliminated in a special recycling center and then, the lift will be removed from the shaft and replaced with generic APEX. Also, here is the list of Russo lift models : - 1rst Gen, produced between Nov. 2008 and Jan. 2012 (You are here). - 2nd Gen, produced since Feb. 2009 and currently still made (Project coming soon). - 3rd Gen, still produced since Jan. 2010 (Coming soon). Also, here is the list of the another next lift projects : - A 2007 Sprinte EV (Inst. Stannah) MRL lift. - A 2008 Sprinte EV (Inst. Stannah) hydro lift. - A 2008 Stannah Hydro MRL. Coming soon. - New APEX MRL. Coming soon. - Russo 1rst Gen lift Orona mod. Coming soon. The factory and the HQ are also located in Nottingham aswell and the factory was making lift parts for the future 1rst Gen lifts between Late September 2008 and the 1st of Nov. 2008. Updates of this lift : 28-29 April : Lift closed and sent up and down until it collapsed. 29 April-4 May : Lift removed and replaced. Replacement is finished and new lift commissioned the 04/05/2023 at 16:00.
Credits to @Jon5432, @vorpsway (Outside direction lift chimes), @StannahHydraulic399 (for some sounds effects), and everyone else that has provided the assets for this project, including the Youtube users Beno, (Creaks, hydro valve, hydraulic ram sounds while the lift is moving, charge, clunks, slowing down door and buttons sounds), Misha Gianoli (Hydraulic pump’s motor), Elevators from France (ram wearing out sound effect while going up), Heritage Elevators (shaking sound effect) and AlexInNorthernIrland (jolt sound when the lift starts moving up as it accelerates from 0 to 0.5 m/s in around 0.15 seconds) but no kirk credits. Also, thanks to TTS.com and Audacity for the voice and the tones (beeps). This building has been built in 2008, this lift has been added in an external shaft when the building has opened and it is the 1rst Russo Elevators Inc lift ever made. Title : RIP ! Nasty, awful and worn-out 2008 Russo Elevators Inc 1rst Gen Hydraulic lift… Manufacturer : Russo Elevators Inc. Model : 1rst Generation. Number of versions : 1. Floors served : 2 to 4. Type of lift : Residential lift for blocks of flats. Quality of that model : Very very low. Life duration before replacement : 7 years to 14 years, 5 months, 3 weeks and a very few days (1-4) maximum. Years of production of this model : Nov. 2008- Jan. 2012. Installed : 1rst week of November 2008. Serial number : RE1G0001 Drive : Roped Hydraulic, 2:1, 1 piston located behind the cab. Type of machinery : Submersible hydraulic pump. Position of the machinery : In a cabinet at ground floor. Motor : REIHydroVator Solutions Ltd RHV 280 (The company which was created by Russo Elevators Inc. to made their hydraulic rams and submersible pump units). Valve : Blain Hydraulics EV 100 (EV 100 0,75’’ version). Hydraulic ram : REIHydroVator Solutions Ltd RHV 40. Buttons : Custom Dewhurst REI-US-91 (The symbols of the buttons are designed by Russo Elevators Inc. but the buttons are manufactured by Dewhurst and branded as REI-US-91 by Dewhurst and Russo Elevators Inc. and these buttons are only used on Russo lifts). Indicators : Dewhurst. Direction jamb arrows : Russo Elevators Inc. Controller : REIElectronics Solutions Ltd MicroComputer MC001 microprocessor controller, full memory. Door equipment : GAL. Phone : REIElectronics Solutions Ltd E-AutoDialleR E- ADR001. Capacity : 630 Kg or 8 Persons. Floors served : 4 (0, 1, 2 and 3). Full speed : 0.5 m/s. Lighting : REIElectronic Solutions Ltd Gen1FLT-type Nr. 00001 fluorescent tubes w/ REIElectronic Solutions Ltd BLE-001 LT001 electronic ballasts. Starter type : Star-Delta. Door sensors : REIElectronic Solutions Ltd Panachrome. Voice : 1rst Gen Russo Elevators Inc. Chimes : 1rst Gen Russo Elevators Inc. + Lester Controls outside direction chimes. Location : A totally random and fictional block of flats (8, Jack Foster Avenue) in Nottingham, UK. Date of footage : 23/04/2023. Maintenance contract : APEX Lifts. My opinion : This Russo Elevators lift is a total « Russo fail-o-vator » ! It shakes like crazy on the way up, spends ages charging the hydraulic, takes a while to level, it’s so slow as it goes 0.5 m/s, the cab creaks all the time while it moves, while the levelling on the way up, the hydraulic ram makes a « worn-out hydraulic piston while the lift levels on the way up noise », the voice is very stupid, very annoying, very dull and says « elevator » nearly all the time, IT’S A LIFT, NOT AN ELEVATOR !!!! The door operator is a stupid clickety, very bog standard and very slow GAL one, the hydraulic valve is a Blain one which is also really really bog standard, the buttons are custom Dewhurst (The symbols are designed by Russo but the buttons are made by Dewhurst) but still incredibly bog standard, the hydraulic pump is cheap and the motor is worn-out, the fluorescent lights/ballasts are buzzing and often burns out, the logic is pretty bad, the chimes and beeps are very loud and annoying, the lift’s structure is so worn out that it will certainly collapse only a few days after I recorded the footage, this semi-generic lift is so cheap and horrid and I cannot find anything good about this lift. That really shows how bad it is, this utter piece of [censored] which is commonly called as a lift TOTALLY SUCKS, it’s SO FREAKING NASTY !!! Even if it has some unique features (Buttons, indicators, some parts are not brought-in-parts, etc…), it is way worse than a generic lift with Lester Controls, a « flatpack lift » (e.g. Kleemann, Sprinte EV/Electra Vitoria, « DMG lifts », « STEP Shangai lifts », IMEM Ascensores…) and even Mac Puarsa lifts are sill better than this load of rubbish (But it’s still better than newer and early 2000’s Omega lifts lol). This lift is also probably much worse than an Otis Genesis and a Schindler 3300/3000/1000 lift or even worse than a Gen2 Home (Utter piece of junk which is very slow, incredibly cheap, ultra flimsy, designed for houses and unreliable). Next part in « Instructions ».
